Kirisun Pt 8000
Main Funciones: ISO9001: 2008 Accredited Designer & Manufacturer ·PTT ID ·Remote Kill/Stun/Activate/Revive ·Remote Background Monitor ·Talk Around ·Public Address ·Lone Work ·Emergency Alarm CTCSS/DCS/DTMF Encoder/Decoder
Frenquency Range 136~174MHz 400~450MHz 438~490MHz 470~512MHz
Channel Capacity 8
Channel Spacing 12.5KHz/25KHz
Frenquency Stability 2.5ppm
Operating temperature -25℃~ + 55℃
Operating voltage 13.6V DC ±20%
Weight(with antenna&battery) 1310g
RF Power 5W/25W
Frenquency modulation 16KφF3E/11KφF3E
Antenna Impedance 50Ω
Modulation Limiting ±2.5KHz@12.5KHz, ±5KHz@25KHz
Modulation Distortion < 5%
Radiated Spurious Emission -36dBm < 1GHz /-30dBm > 1GHz
FM Noise -40dB @ 25KHz/-35dB @ 12.5KHz
Adjacent Channel Power -60dB @ 12.5KHz/-70dB @25KHz
Reference Sensitivity 0.28μV@12.5KHz 0.25μV@25KHz typical
Operating Bandwidth W≥±7 N≥±3.5
First IF of Receiver 49.95
Second IF of Receiver 450
Adjacent channel Selectivity 60dB @ 12.5KHz 70dB @ 20/25KHz
Intermodulation Rejection 65 dB
Spurious Response Rejection 70 dB
Rated Audio Power 4W
Rated Audio Distortion 5%
FM Hum&Noise 40/35
*CTCSS / DCS
38 groups of standard CTCSS and 83 groups DCS are available (PC programmable).
Built-in CTCSS/DCS Encoder/Decoder can prevent co-channel interference and
unwanted conversations on the same frequency and ensure smooth communication.
Programmable DTMF settings could be used for dispatch operations and remote
*Easy-to-switch RF power
Each channel or all channels could be set to high or low RF power for different
applications by programming software or manually.
If the radio is killed or stunned, all attempts on operation by user, except power on/off,
will be ignored. The radio will be activated or revived only when it received the correct
*Public Address (PA)
The PA feature feeds MIC audio through a powerful external public address amplifier,
and outputs through external speaker, offering robust clarity in harsh, noisy
This feature allows user prompt reset the RX and TX frequency to be same and offers
the possibilities of communication among radios in system without repeater.
The radio can be programmed to alarm local or secretly, to alarm with sending
emergency code and alert or background sound for different emergency
A certain code could be programmed with press or/and release of PTT button to notify
the other people who is the caller.
The radio could respond to a preprogrammed code automatically and silently to make
sure the user is in effective communication area.
*Lone Work & Security Check
The radio enters emergency mode if the user does not respond to a warning call
(Lone Work) or a inquire code (Security Check), adding security and safety for
individuals who work remotely and lonely. To prevent any carelessly missing, the reset
of lone work status could be by simply press on programmed key.
*Remote Background Monitor
Background sound could be monitored by remote receiver with specific code.
The radio could continuously scan each channel in the scan list for active
conversation. Simply press a preset key to activate scan. Priority scan and talk
channel (revert channel) could be set too.
Individual call or group call could be activated by press on preprogrammed Call keys.
With different preset code, user can make two different calls in each channel.
*Busy Channel Lockout (BCLO)
BCLO is used to prevent the interference with the on-going conversation. If BCLO is
on, the radio will be remaining in receiving status even with PTT pressed to avoid
interfering with others on conversation.
*Time-out Timer (TOT)
When TOT is on and the transmission exceeds the preset time limit, the radio will stop
after warning tone. TOT can prevent the radio from any potential damage caused by
To monitor whether the current channel has signal, pressing the preprogrammed key.
The Monitor function is used to receive weak signal.
Up to 5 programmable keys could be set as different functions by hold or press it.
The radio offers reading and writing password to protect the privacy and prevent
unauthorized modification of radio data.
To quickly set the parameters on a radio, the radio data could be cloned from another
radio with cloning cable, saving the time of parameter setting.
The radio installed on car could be powered on automatically with the car started.
*Programmable Squelch Level (SQL)
*Embedded Radio Information